Page Map

 WPP Home

My Gun Doctor

Gunsmithing Services

 

We do NOT perform any warranty work

MINIMUM CHARGE PER GUN $35.00

 

Per Man Hour $45.00 (Billed in Tenths)

Per Man & Machine Hour $75.00 (Billed in Tenths)

Written appraisals, written cost estimates $50.00

 

CLEAN & OIL CUSTOMER GUN

 

Consisting of completely stripping gun, cleaning all parts, checking for wear,

making suggestions to a customer of services needed to put in A-1 condition $50.00

 

METAL FINISHING

 

BAKING LACQUER FINISH/TEFLON-MOLY FINISH $150.00

 

BEADBLAST, SANDBLAST, OR WIRE BRUSH STAINLESS STEEL $125.00

 

ELECTROLESS NICKEL PLATING

 

Handguns or small parts only

 

High polish $235.00

Satin finish $200.00

 

Rifles/shotguns

 

High polish $250.00

Satin finish $190.00

 

STRIPPING NICKEL

Removing old nickel finish prior to bluing or replating $150.00

 

PARKERIZING $135.00

 

COLOR CASE HARDENING $450.00

 

ENGINE-TURNING BOLT Hourly Rate

 

ENGINE-TURNING SMALL PARTS Hourly Rate

 

 

 

 

 

SIGHT WORK

 

SIGHT IN CUSTOMER GUN - Does not include cost of ammo, targets, etc. $75.00

 

BORE SIGHTING CUSTOMER GUN $35.00

 

PATTERN SHOTGUN - Does not include cost of ammo, targets, etc. $65.00

 

DRILL AND TAP BARREL OR RECEIVER FOR SIGHTS

Per hole $20.00

 

CUT DOVETAIL IN BARREL $95.00

 

INSTALL FRONT SIGHT RAMP

Sweat-on type $75.00

Screw-on type (including drill & tap) $65.00

Band type Hourly Rate

 

INSTALL INSERT IN PISTOL SIGHT $50.00

 

INSTALL FRONT OR MID-RIB BEAD

 

ON SHOTGUN (Plus cost of sight) $45.00

Plug hole and re-drill for bead $65.00

 

INSTALL RECEIVER SIGHTS

Gun drilled and tapped $35.00

 

SCOPE MOUNTING

Gun drilled and tapped $35.00

 

FABRICATE CUSTOM WEAVER BASE $45.00

 

FABRICATE CUSTOM DOVETAIL BASE $40.00


GENERAL BARREL, ACTION & RIFLE WORK

 

CHECK HEADSPACE $55.00

 

MAKE CHAMBER CAST $65.00

 

REMOVE STUCK FIRED CASE FROM CHAMBER Hourly Rate

 

REMOVE LIVE ROUND FROM CHAMBER (Priced on Request)

 

REMOVE OBSTRUCTION FROM BORE Hourly Rate

 

REMOVE FOULING FROM BARREL Hourly Rate + Materials

 

LAP BARREL $130.00

 

INSTALL LINER IN BARREL - Not including cost of liner or bluing $225.00

 

CUT AND CROWN BARREL

Rifles, Shotguns, and Handguns $95.00

 

CHAMBER AND FIT BARREL TO ACTION

Does not include the cost of the barrel, action, polishing, bluing $200.00

 

INSTALL PRE-THREADED AND CHAMBERED BARREL

- Not including Polishing & Bluing $125.00

 

LAP IN BOLT LUGS - Not including setting back barrel or fitting new barrel $65.00

 

WELDING ON NEW BOLT HANDLE $90.00

 

FORGING BOLT HANDLE $115.00

 

MAKE AND INSTALL SPRING Hourly Rate

 

SAFETIES, INSTALLING,

Dakota, Gentry, Mod 70 Type Safety w/shroud (+ finishing) $150.00

Mark II/Beuhler type $70.00

Chapman Swing Safety Lever $135.00

 

TRIGGERS (INSTALLATION OR ADJUSTMENT)

Shilen, Timney, Dayton-Traister, Moyer type $90.00

Double-Set $250.00

Single Set $140.00

 

INSTALL MUZZLE BRAKE $120.00

 

RECONTOUR FRONT OR REAR RECEIVER RING $140.00

 

INSTALL BARREL BAND SWIVEL Hourly Rate

 

SHOTGUN WORK

 

CHECK CHAMBER & HEADSPACE $45.00

 

LONG FORCING CONE

Non-plated bores, per barrel $40.00

Plated bores, per barrel $80.00

 

RESOLDER RIB - Not including bluing, Hourly Rate

 

RESOLDER FOREND LUG - Not including bluing, Hourly Rate

 

RAISING DENT IN BARREL - Not including bluing $120.00

 

STRAIGHTEN / ADJUST BARREL $95.00

 

POLISH CHAMBER/BORE $75.00

 

BACK-BORING - Per Barrel, non-plated bores, Hourly Rate

 

OPEN UP or MODIFY CHOKE

Per barrel or tube, non-plated bores $75.00

 

INSTALL SCREW-IN CHOKE (includes one extended ported choke tube)

(non-plated bore) $120.00 per barrel

 

PORT BARREL - PER BARREL $100.00 (Standard Porting Arrangement)

 

REFITTING HINGE PIN LUG $250.00

 

CORRECT HEADSPACE (Priced on Request)

 

HONE CHAMBER $35.00

 

 

STOCK WORK

 

WOOD FINISHING (Does not include any shaping)

 

Hunter Finish

Unfilled oil or lacquer finish on average stock $150.00

Same finish but on a complicated stock $175.00

 

Gunsmith Finish

Filled, rubbed oil finish on average stock $210.00

Same finish but on a complicated stock $275.00

 

Spray Finish

Lacquer or polyurethane $160.00

 

RECUTTING CHECKERING - Other than by the hour, per panel

Simple pattern $120.00

Complicated pattern $170.00

 

 

GLASS BEDDING BARREL & ACTION

Hunting Rifle $150.00

Match Rifles, M-1 Garand, M1A, etc. $225.00

Pillar Bed $165.00

 

INSTALL RECOIL PAD - Labor only $55.00

 

INSTALL ADJUSTABLE BUTT PLATE - Labor only $100.00

 

INSTALL SLING SWIVELS - Std and Q/D $35.00

 

INSTALL STOCK CROSS BOLT (Not including refinish) $65.00

 

INSTALL RECOIL REDUCER

Simple installation in butt stock $35.00

Hydraulic butt plate-style (Gra-Coil or Counter Coil) $125.00

Drill Stock & Install Recoil Reducer $95.00

 

 

INLETTING AND FINISHING OF SEMI-FINISHED STOCK

Not including checkering, recoil pad, special butt plate, grip cap or other

attachments (Priced on Request)

 

FIT, BED AND FINISH FIBERGLASS STOCK BLANK (Priced on Request)

 

PREFINISHED SYNTHETIC STOCK

Fit and install barreled action $100.00

 

CAMO PAINTING STOCK $125.00

 

INSTALL ADJUSTABLE COMB HARDWARE $225.00

 

ALWAYS CALL BEFORE SHIPPING ANY FIREARM